水泥穩定碎石的壓實控制標準主要依據公路的等級和用途來確定。以下是一些具體的壓實控制標準：

　　The compaction control standards for cement stabilized crushed stone are mainly determined based on the grade and purpose of the highway. Here are some specific compaction control standards:

　　一、壓實度要求

　　1、 Compaction requirements

　　對于高速公路和一級公路的基層，水泥穩定碎石材料的壓實度應達到98%。

　　For the base course of expressway and first-class highway, the compactness of cement stabilized crushed stone material shall reach 98%.

　　對于高速公路和一級公路的底基層，水泥穩定碎石材料的壓實度應達到97%。

　　For subbase of expressway and first-class highway, the compactness of cement stabilized crushed stone material shall reach 97%.

　　這些壓實度要求確保了公路基層和底基層的穩定性和承載能力。

　　These compaction requirements ensure the stability and bearing capacity of the highway base and subbase.

　　二、施工工藝與設備

　　2、 Construction technology and equipment

　　在施工過程中，應采用集中廠拌混合料，并使用攤鋪機攤鋪、壓路機碾壓的施工工藝。

　　During the construction process, a centralized factory mixed mixture should be used, and the construction technology of paving with a paver and rolling with a roller should be employed.

　　壓路機的選擇應根據具體的施工條件和要求來確定，但通常應配備振動壓路機和輪胎壓路機進行碾壓。

　　The selection of road rollers should be determined based on specific construction conditions and requirements, but vibration rollers and tire rollers should usually be equipped for rolling.

　　三、其他控制因素

　　3、 Other control factors

　　含水量：應在混合料略大于最佳含水量的1個百分點時進行碾壓，以確保達到規定的壓實度。

　　Moisture content: Rolling should be carried out when the mixture is slightly above 1 percentage point of the optimal moisture content to ensure that the specified compaction degree is achieved.

　　延遲時間：從加水拌和到碾壓終了的延遲時間不應超過水泥的初凝時間，以避免混合料硬化和壓實效果不佳。

　　Delay time: The delay time from mixing with water to the end of compaction should not exceed the initial setting time of cement to avoid poor hardening and compaction effect of the mixture.

　　配合比：應嚴格按照設計要求的配合比進行拌和，確?；旌狭系木鶆蛐院头€(wěn)定性。

　　Mix proportion: The mixing should be strictly carried out according to the design requirements to ensure the uniformity and stability of the mixture.

　　四、檢測與評定

　　4、 Testing and evaluation

　　在施工過程中，應定期對壓實度進行檢測，可以采用核子密度儀或灌砂法等方法進行檢測。

　　During the construction process, the compaction degree should be checked regularly, and methods such as nuclear density meter or sand filling method can be used for testing.

　　評定標準應依據《公路工程質量檢驗評定標準》等相關規范進行。

　　The evaluation criteria should be based on relevant specifications such as the "Quality Inspection and Evaluation Standards for Highway Engineering".

　　綜上所述，水泥穩定碎石的壓實控制標準是一個綜合性的要求，包括壓實度、施工工藝與設備、其他控制因素以及檢測與評定等多個方面。這些標準的嚴格執行可以確保公路基層和底基層的穩定性和承載能力，提高公路的使用壽命和安全性。

　　In summary, the compaction control standard for cement stabilized crushed stone is a comprehensive requirement, including compaction degree, construction technology and equipment, other control factors, and detection and evaluation. The strict implementation of these standards can ensure the stability and bearing capacity of highway base and subgrade, and improve the service life and safety of highways.

　　本文由  濟南水泥穩定碎石 友情奉獻.更多有關的知識請點擊  http://m.sybloom.com   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Cement Stabilized Crushed Stone For more related knowledge, please click http://m.sybloom.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.