公司新聞
攤鋪機工作前和工作時的注意事項
來源：http://m.sybloom.com/ 日期：2023-06-14
攤鋪機工作前的注意事項：
Precautions before the paver works:
1、發動機轉速未達到1600rpm時，各種動作的操作均無效。
1. When the engine speed does not reach 1600rpm, all actions are ineffective.
2、在啟動發動機時，必須將行走操縱桿置于中位。
2. When starting the engine, the travel control lever must be placed in the neutral position.
3、柴油機啟動后保證電瓶充電指示燈和柴油機機油壓力報警燈（綠色）熄滅。
3. After the diesel engine starts, ensure that the battery charging indicator light and the diesel engine oil pressure alarm light (green) turn off.
4、各報警燈發出信號，必須認真查清原因、排除故障，并及時報告、記錄，否則機器不能移動。
4. When each alarm light emits a signal, it is necessary to carefully investigate the cause, eliminate the fault, and report and record in a timely manner, otherwise the machine cannot move.
5、在給液壓油箱加油時，必須用過濾精度為10μm的過濾機加油！
5. When refueling the hydraulic oil tank, a filtration accuracy of 10 must be used μ M's filter refueling!
6、提升熨平板時，必須將找平油缸提升到中位以上，否則，有損壞機器的可能。
6. When lifting the iron plate, the leveling cylinder must be raised above the center position, otherwise there is a possibility of damaging the machine.
7、螺旋分料裝置安裝時請將腳踏柵格插入擋板上的孔內，予以覆蓋分料桿通道。
7. When installing the spiral dividing device, please insert the foot grid into the hole on the baffle to cover the dividing rod channel.
8、在裝卸找平儀的過程當中防止磕碰，輕拿輕放，并注意超聲波探頭上不要沾上油污等并始終保持探頭表面的清潔。
8. During the process of loading and unloading the leveling instrument, prevent collisions, handle it gently, and pay attention not to get oil stains or other substances on the ultrasonic probe, and always keep the surface of the probe clean.
然后濟南攤鋪機出租廠家再來講講攤鋪機工作時的注意事項：
Then, the rental manufacturer of Jinan pavers will talk about the precautions for paver operation:
1、攤鋪機工作時，無論攤鋪的是什么樣的材料、什么樣的寬度，必須將油門開至大位置—即額定轉速狀態，否則攤鋪機工作將不正常。
1. When the paver is working, regardless of the type of material and width being paved, the throttle must be turned to a high position - that is, the rated speed state, otherwise the paver will not work properly.
2、攤鋪機在待料的過程當中，發動機怠速的時間不能太長（長不超過5分鐘），否則會損壞發動機。
2. During the waiting process of the paver, the idle time of the engine should not be too long (no more than 5 minutes), otherwise it will damage the engine.
3、隨時注意檢查發動機機油壓力和工作溫度是否正常。如有不正常情況，則應停機檢查排除故障。
3. Check whether the engine oil pressure and operating temperature are normal at any time. If there are abnormal situations, the machine should be shut down for inspection and troubleshooting.
4、注意觀察液壓油箱溫度計，其溫度指示不得高于80℃，否則要停機檢查原因。
4. Pay attention to observing the temperature gauge of the hydraulic oil tank. The temperature indication should not exceed 80 ℃, otherwise the machine should be shut down to check the cause.
5、注意攤鋪機各零部件有無松動或不正常的聲響。如有則應停機檢查。
5. Pay attention to whether the components of the paver are loose or have abnormal noises. If there is, it should be stopped for inspection.
6、注意攤鋪機的發電機或其他電器元件有無過熱而燒焦的氣味。如有則應停機檢查。
6. Pay attention to the generator or other electrical components of the paver for any odor of overheating and burning. If there is, it should be stopped for inspection.
7、注意各系統有無泄漏發生，有則應停機檢查排除故障。
7. Pay attention to whether there are any leaks in each system, and if there are, shut down the machine for inspection and troubleshooting.
攤鋪機工作前和工作時的注意事項就講解到這里了，希望能夠給您好的幫助，更多事項就來我們網站http://m.sybloom.com咨詢！
That's all for the precautions before and during the operation of the paver. I hope you can be helpful. For more information, please visit our website http://m.sybloom.com consulting service
公司地址：濟南市商河縣賈莊鎮民營經濟創業園
公司名稱:永誠廣建公路材料（山東）有限公司 
備案號：